View IGMP Group Information

View information about IGMP groups to see the current group operation on the switch.

Procedure

Enter Privileged EXEC mode:

enable
View IGMP group information:

show ip igmp group group <A.B.C.D> detail [port {slot/port[/sub-port][-slot/port[/sub-port]][,...]}][vlan <1-4059>] [vrf WORD <1–16>][vrfids WORD <0–512>]

show ip igmp group group <A.B.C.D> tracked-members [member-subnet <A.B.C.D./X>][port {slot/port[/sub-port][-slot/port[/sub-port]][,...]}] [source-subnet <A.B.C.D/X>] [vlan <1-4059>][vrf WORD <1–16>][vrfids WORD <0–512>]

Example

View IGMP group information:

Switch:1>enable
Switch:1#show ip igmp group group 232.0.0.0
 
================================================================================
                           Igmp Group - GlobalRouter
================================================================================
GRPADDR         INPORT          MEMBER          EXPIRATION TYPE
--------------------------------------------------------------------------------
232.0.0.0       V1015-1/2       200.0.15.53     258        Dynamic

1 out of 271 group Receivers displayed

Total number of unique groups 271

Variable Definitions

The following table defines parameters for the show ip igmp group command.


Variable	Value
count	Displays the number of entries in the IGMP group.
group `<A.B.C.D>`	Specifies the address of the IGMP group.
member-subnet {default\| `<A.B.C.D>`}]	Specifies the IP address and mask of the IGMP member.
vrf `WORD<1–16>`	Specifies the VRF name.
vrfids `WORD<0–512>`	Specifies the VRF ID.

The following table defines parameters for the show ip igmp group group command.


Variable	Value
detail [port `{slot/port[/sub-port][-slot/port[/sub-port]][,...][slot/all][all]}`\|vlan `<1-4059>`\|vrf`WORD <1–16>`\|vrfids`WORD <0–255>`]	Use the detail parameter to show IGMPv3–specific data. For data related to a specific interface use the following: port`{slot/port[/sub-port][-slot/port[/sub-port]][,...][slot/all][all]}` — Specifies the port list. vlan `<1-4059>`— Specifies the VLAN. Specifies the VLAN ID in the range of 1 to 4059. By default, VLAN IDs 1 to 4059 are configurable and the system reserves VLAN IDs 4060 to 4094 for internal use. On switches that support the vrf-scaling and spbm-config-mode boot configuration flags, if you enable these flags, the system also reserves VLAN IDs 3500 to 3998. VLAN ID 1 is the default VLAN and you cannot create or delete VLAN ID 1. vrf `WORD<1–16>` — Specifies the VRF name. vrfids `WORD<0–255>` — Specifies the VRF ID.
tracked-members	Use the tracked-members parameter to view all the tracked members for a specific group.
vrf `WORD<1–16>`	Specifies the VRF name.
vrfids `WORD<0–512>`	Specifies the VRF ID.

The following table defines parameters for the show ip igmp group group <A.B.C.D> tracked-members command.


Variable	Value
member-subnet {default\| `<A.B.C.D>`}]	Specifies the IP address and mask of the IGMP member.
port `{slot/port[/sub-port][-slot/port[/sub-port]][,...][slot/all][all]}`	Specifies the port list.
source-subnet`<A.B.C.D/X>`	Specifies the source IP address and the subnet mask.
vlan `<1-4059>`	Specifies the VLAN ID in the range of 1 to 4059. By default, VLAN IDs 1 to 4059 are configurable and the system reserves VLAN IDs 4060 to 4094 for internal use. On switches that support the vrf-scaling and spbm-config-mode boot configuration flags, if you enable these flags, the system also reserves VLAN IDs 3500 to 3998. VLAN ID 1 is the default VLAN and you cannot create or delete VLAN ID 1.
vrf `WORD<1–16>`	Specifies the VRF name.
vrfids `WORD<0–512>`	Specifies the VRF ID.